BTS INSTALLATION GUIDE

Toyota Tundra SS20 TRD Pro grille installation guide

Install the Standard SS20 kit behind an OEM TRD Pro grille on a supported 2022–2026 Toyota Tundra, with the manufacturer’s original mounting and wiring photographs.

View the matching kit

Check the vehicle and supplied kit

An OEM TRD Pro grille is required and is not included. Aftermarket grille fitment is not established. Use the supplied harness and new switch; the factory TRD Pro light switch is incompatible. The original shared article also mentions Classic SS18: this guide follows the current SS20 mounting branch and does not substitute SS18 wiring, power or controls.

Tools: Ratchet; 10 mm and 12 mm sockets; T6 Torx driver; Phillips screwdriver; suitable trim tools.

Park securely, switch the vehicle off and follow its service instructions for electrical isolation and safety-related fasteners. Use a qualified installer if you are not equipped for the work. Compare the supplied connectors and hardware with the exact instructions before proceeding. Original photographs and annotations remain intact; open any figure at full size.

1. Release the upper bumper

Open the hood. Remove the four upper bumper bolts with a 10 mm socket and the two push clips with a trim tool. Disconnect the four harness connectors beside the clips.

Original manufacturer figure for step 1: release the upper bumper.
Original manufacturer figure for step 1: release the upper bumper. Open original figure

2. Release the lower bumper

Remove the four lower bumper bolts with the 10 mm socket. Keep removed hardware organised for reassembly.

Original manufacturer figure for step 2: release the lower bumper.
Original manufacturer figure for step 2: release the lower bumper. Open original figure

3. Open both wheel-well areas

Remove the five 10 mm fasteners in each wheel well. Move the liners aside enough to reach the bumper clips.

Original manufacturer figure for step 3: open both wheel-well areas.
Original manufacturer figure for step 3: open both wheel-well areas. Open original figure

4. Release the fender flares

Reach behind each flare and release its two bumper clips. Ease the flare away without forcing it; repeat on the other side.

Original manufacturer figure for step 4: release the fender flares.
Original manufacturer figure for step 4: release the fender flares. Open original figure

5. Remove and support the bumper

Release the bumper from each wheel-well edge toward the centre. Lift it away carefully and place it face down on a protected, padded surface.

Original manufacturer figure for step 5: remove and support the bumper.
Original manufacturer figure for step 5: remove and support the bumper. Open original figure
Original manufacturer figure for step 5: remove and support the bumper.
Original manufacturer figure for step 5: remove and support the bumper. Open original figure

6. Remove the active grille shutter

Disconnect the shutter harness and remove the six 10 mm fasteners shown. Put the shutter assembly aside safely.

Original manufacturer figure for step 6: remove the active grille shutter.
Original manufacturer figure for step 6: remove the active grille shutter. Open original figure

7. Remove the radar assembly

Remove the two bolts and Phillips screw at the radar sensor. Retain the slide nuts and release the sensor-cover clips for later reinstallation.

Original manufacturer figure for step 7: remove the radar assembly.
Original manufacturer figure for step 7: remove the radar assembly. Open original figure

8. Remove the camera bracket

Remove the two Phillips screws holding the camera bracket. Record the camera orientation before moving it.

Original manufacturer figure for step 8: remove the camera bracket.
Original manufacturer figure for step 8: remove the camera bracket. Open original figure

9. Separate the camera from its mount

Disconnect the camera harness. Remove its two T6 Torx screws and retain them with the camera.

Original manufacturer figure for step 9: separate the camera from its mount.
Original manufacturer figure for step 9: separate the camera from its mount. Open original figure

10. Release the upper grille surround

Remove the four Phillips screws and release the upper surround clips. Support the panel as the last clips release.

Original manufacturer figure for step 10: release the upper grille surround.
Original manufacturer figure for step 10: release the upper grille surround. Open original figure

11. Release the left surround

Remove the two Phillips screws and release the clips on the left grille surround.

Original manufacturer figure for step 11: release the left surround.
Original manufacturer figure for step 11: release the left surround. Open original figure

12. Release the right surround

Repeat the two-screw and clip removal on the right grille surround.

Original manufacturer figure for step 12: release the right surround.
Original manufacturer figure for step 12: release the right surround. Open original figure

13. Release the lower surround

Release the retaining clips along the lower grille surround and lift it away.

Original manufacturer figure for step 13: release the lower surround.
Original manufacturer figure for step 13: release the lower surround. Open original figure

14. Remove the original grille

Remove the four Phillips screws and the remaining clips securing the grille.

Original manufacturer figure for step 14: remove the original grille.
Original manufacturer figure for step 14: remove the original grille. Open original figure

15. Fit the OEM TRD Pro grille

Position the OEM TRD Pro grille, seat its clips and reinstall the screws. The grille is required but is not supplied with this light-bar kit.

Original manufacturer figure for step 15: fit the oem trd pro grille.
Original manufacturer figure for step 15: fit the oem trd pro grille. Open original figure

16. Refit the radar assembly

Reinstall the radar sensor and cover using the retained factory hardware and slide nuts. Preserve its original orientation.

Original manufacturer figure for step 16: refit the radar assembly.
Original manufacturer figure for step 16: refit the radar assembly. Open original figure

17. Refit the surrounds

Refit the lower, left, right and upper surrounds, in that order. Check clip engagement before moving on.

Original manufacturer figure for step 17: refit the surrounds.
Original manufacturer figure for step 17: refit the surrounds. Open original figure

18. Relocate the camera

Attach the camera to the supplied relocation mount with the original T6 screws. Follow the illustrated locking-tab orientation when seating the mount in the grille.

Original manufacturer figure for step 18: relocate the camera.
Original manufacturer figure for step 18: relocate the camera. Open original figure

19. Mount the SS20 in its bracket

Use the supplied hardware to fit the SS20 in the grille bracket, with its harness toward the keyhole end. Slide the bar fully forward and leave the hardware loose enough for final aiming. The manufacturer states that this mounting procedure is shared with the earlier SS18; the original photograph illustrates bracket position, not the SS20 lamp specification.

Original manufacturer figure for step 19: mount the ss20 in its bracket. The shared mounting photograph shows earlier hardware; the current written SS20 mounting instructions control.
Original manufacturer figure for step 19: mount the ss20 in its bracket. The shared mounting photograph shows earlier hardware; the current written SS20 mounting instructions control. Open original figure

20. Attach the grille bracket

Secure the bracket to the TRD Pro grille with the supplied screws and washers. Do not overtighten the grille fasteners.

Original manufacturer figure for step 20: attach the grille bracket.
Original manufacturer figure for step 20: attach the grille bracket. Open original figure

21. Fit both support brackets

Fit the upper and lower support brackets with the supplied hardware. Align the locations marked in the original figure before tightening.

Original manufacturer figure for step 21: fit both support brackets.
Original manufacturer figure for step 21: fit both support brackets. Open original figure

22. Route the bar connector

Run the bar harness along the grille and secure it with the supplied ties, leaving the connectors and nearby hardware clear.

Original manufacturer figure for step 22: route the bar connector.
Original manufacturer figure for step 22: route the bar connector. Open original figure

23. Refit the shutter with its spacers

Use the supplied spacers when reinstalling the active grille shutter. Reconnect its harness and preserve the bar’s fully forward position.

Original manufacturer figure for step 23: refit the shutter with its spacers.
Original manufacturer figure for step 23: refit the shutter with its spacers. Open original figure

24. Refit the bumper

Return the bumper to the vehicle and reverse the removal sequence. Reconnect the disconnected vehicle harnesses and check that the surrounding panels are seated.

Original manufacturer figure for step 24: refit the bumper.
Original manufacturer figure for step 24: refit the bumper. Open original figure

25. Wire the correct power branch

Use the included harness and its new switch; the factory TRD Pro light switch does not control this bar. On a hybrid, remove the fuse cover and use the illustrated positive post (12 mm nut) and ground point (10 mm bolt). On a non-hybrid, the manufacturer uses the battery positive and negative terminals with 12 mm hardware. Follow the vehicle manufacturer’s battery-isolation precautions before electrical work. Route the light-bar output to the front passenger side and the switch lead to the driver-side grommet beside the brake booster. Secure the loom clear of heat, sharp edges and moving parts. The two original figures show the hybrid and non-hybrid branches respectively.

Original manufacturer figure for step 25: wire the correct power branch.
Original manufacturer figure for step 25: wire the correct power branch. Open original figure
Original manufacturer figure for step 25: wire the correct power branch.
Original manufacturer figure for step 25: wire the correct power branch. Open original figure

26. Test, aim and finish

After safely restoring power, test the bar and set its aim. Tighten the mounting hardware with the 10 mm socket. Confirm that the fully forward bar and the installed spacers allow the active grille shutter to move without interference.

Original manufacturer figure for step 26: test, aim and finish.
Original manufacturer figure for step 26: test, aim and finish. Open original figure

Tundra TRD Pro grille installation

This original installation video can show the older SS18 bar. Use the current SS20 written steps above, the supplied harness and a new switch.

Original instructions and matching kit

This BTS guide uses original explanatory wording with all relevant original technical figures from the manufacturer’s current HTML article. The article does not provide a downloadable PDF.

Read the original Diode Dynamics instructions

Return to the matching kit