MORIMOTO XB EVO · LF2-533
Tri-Beam light for your Tundra or Sequoia.
A complete left/right XB Evo headlight pair for your 2007–2013 Tundra / 2008–2017 Sequoia. Configurable white or amber daytime running lights, a startup welcome sequence and Frost-Free lens heating bring a modern lighting signature to your truck.
- Left + rightOne complete headlight pair
- White / amber DRLsConfigurable signals
- Tri-Beam opticsBuilt for the exact application

THE OPTICS FOR YOUR TRUCK
Tri-Beam optics. A matched pair.
Light where it belongs
Each housing combines a Type 1 Ishida Bi-LED projector with a low-beam reflector assist and a high-beam reflector assist. Both Evo and Hybrid retain this Tri-Beam layout.
Complete headlight assemblies
Both housings and the exact listed wiring parts are supplied. This replaces the headlight assemblies, rather than converting a bulb inside the old housing.
Finish with correct aim
Check and adjust beam aim after installation. Original mounting points and a stock ride height do not remove the need to verify alignment.

TRI-BEAM TECHNOLOGY
A projector, with dedicated reflector support
Morimoto’s diagram explains the optical layout. It is an illustration of the system, not an independent measured-output test.

SEE THE MANUFACTURER COMPARISON
Low beam and high beam, with the configuration shown
These are Morimoto’s original comparison images, not an independent BTS test. Read the original-lamp and driver labels to understand each example. Supercharged configurations are for off-road use only.

YOUR FRONT-END SIGNATURE
Choose white or amber. Set your signal style.
The supplied selector keys configure white or amber daytime running lights and sequential or fade-off turn signals. Choose matching keys for both headlights with the vehicle and lamps switched off, following the exact guide.
A multistage welcome sequence adds a startup signature. It is a styling feature, separate from driving-light output.

FROST-FREE LENS HEATING
Request it when cold-weather conditions call for it
The logic-controlled 50W ceramic heating element and circulation fans warm the housing to help mitigate lens frost, snow and ice buildup during driving.
- With the vehicle running, wait until the welcome sequence completes.
- Flash the high beams four times within four seconds. The ambient sensor must read at or below 5°C / 41°F, and the other operating conditions must be satisfied.
- Two return flashes indicate active heating and fans. One acknowledges the request with conditional standby.
The system monitors lens and heater temperatures and battery voltage. It starts off at every ignition cycle; request it again when needed. The same four flashes within four seconds manually disable it.
This is an aid during inclement driving, not a system intended to melt heavy overnight snow accumulation.
If the request is not acknowledged, the guide recommends turning off auto high beams and trying again.

CHOOSE THE FEATURES YOU WANT
Compare the matching Evo pair
This listing is LF2-533 XB Evo. The matching Evo and Hybrid are separate products. On smaller screens, swipe across the table to compare every column.
| Feature | XB Evo | XB Evo Hybrid |
|---|---|---|
| Main optics per housing | Bi-LED + low/high reflector assist | Bi-LED + low/high reflector assist |
| Daytime running lights | Selectable white / amber | Fixed white |
| Turn signals | Sequential or fade-off | Fade-off |
| Lens heating | Frost-Free; driver-requested | Not included |
| Standard welcome sequence | Included | Not included |
| Optional Supercharged pair | LF2-DRVSC11; off-road only | LF2-DRVSC11; off-road only |

BEFORE YOU ORDER
Match the year, model and original lamps
| Vehicle | Manufacturer-listed application |
|---|---|
| Toyota Tundra | 2007-2013 (All) |
| Toyota Sequoia | 2008-2017 (All) |
Developed for North American left-hand-drive vehicles using right-hand traffic. Morimoto does not guarantee compatibility outside North America.
The exact pair fits 2007–2013 Tundra and 2008–2017 Sequoia. The supplier’s Tundra and Sequoia photographs show the same part in both listed vehicles. Retained motorized adjusters continue the applicable original in-cab adjustment function; this does not add a function to a vehicle that did not have it.
BOTH SIDES. THE MATCHED HARDWARE.
What is supplied

- Headlights: One Pair (1x RH / Passenger Side Headlight, 1x LH / Driver Side Headlight)
- Accessories: 2x Input Harnesses, 2x Magnet Mount Resistors, 1x Fuse Tap, 1x DRL Harness, 8x (Four Pairs) Mode Selectors, 2x 10mm Mounting Bolts
Use the adapters and signal components appropriate to the truck’s original lighting. Any optional accessories are separate selections; the listed standard installation parts are supplied with the headlight pair.
FACTORY MOUNTING. CAREFUL WIRING.
Plan the installation, then set the aim
- Follow the exact model-family guide and the wiring branch for your original lighting equipment.
- Fit the specified input harnesses and signal components, mount both housings at the original locations and route the DRL harness securely.
- The guide requires a notch in the fuse-box lid for the DRL wire and grommet. Factory mounting points do not mean a completely modification-free installation.
- Secure wires away from heat and moving parts, confirm every lighting function, then adjust the headlight aim.
Download the official LF2-533 model-family installation guide
Heater activation applies only to the heated Evo, and the feature defaults off after each ignition cycle.

AN OPTIONAL OFF-ROAD CONFIGURATION
Add the exact Supercharged driver pair
Standard LED drivers are included. The matching optional pair is LF2-DRVSC11. Select the matching Supercharged option with the headlight if you want that separate configuration.
For this exact application, Morimoto describes approximately 30% greater low/high-beam intensity. This is the manufacturer’s comparison, not an independent BTS measurement or a guarantee in every condition.

THE EXACT LF2-533 CONFIGURATION
Specifications and replacement references
| Detail | Manufacturer specification |
|---|---|
| Traffic Pattern | LHD / Right Hand Traffic Only (US/CA Standard) |
| Output (Standard Drivers) | DOT (FMVSS108) Compliant (LB2V and UB2) |
| Output (Supercharged Drivers) | Off-Road use only |
| Main Optics | 1x Type 1 Ishida Optic Bi-LED, 1x Low-Beam Reflector Assist, 1x High-Beam Reflector Assist |
| Functions | Low, High, Park, Turn, DRL, Welcome, and Lens Heating |
| Turn Signal Modes | Sequential or Fade Off (Configurable) |
| DRL Colors | White or Amber (Configurable) |
| Frost-Free System | Logic-controlled 50w ceramic w/ circulation fans |
| Internal Finish | Two-Tone Piano Black and Titanium w/ contrasting textures |
| Side marker | Amber side reflex reflector (DOT compliant) |
Original-equipment replacement references
81130-0C051, 81130-0C070, 81170-0C051, 81170-0C070, 81110-0C051, 81110-0C070, 81150-0C051, 81150-0C070
Confirm the exact year, model and original lamp equipment above.
Morimoto provides a 5-year limited manufacturer warranty. Coverage, exclusions and return authorization follow the manufacturer’s current policy. Keep your proof of purchase and contact BTS before removing a lamp for a suspected warranty issue.
SEE THE DESIGN
Watch the official overview
Morimoto’s official Tundra / Sequoia model-family presentation. Other versions may appear; use this page’s exact LF2-533 package and specifications for your selection.

The video loads only when you choose it. No autoplay. Product-family demonstrations may include other options; the exact package and compatibility notes on this page govern your selection.
CLEAR ANSWERS BEFORE CHECKOUT
Your XB Evo questions
Is this one lamp or a pair?
One order supplies both driver-side and passenger-side headlight assemblies with the listed accessories.
Which vehicles does this exact part fit?
2007–2013 Tundra / 2008–2017 Sequoia. Match the exact original lamp equipment and wiring described in the guide.
What optics does the Hybrid keep?
The Toyota Hybrid retains the Tri-Beam layout: one Bi-LED projector plus low- and high-beam reflector assist in each housing.
Can I choose white or amber DRLs?
Yes. Use the supplied selector keys for white or amber DRLs and sequential or fade-off signals. Follow the guide and switch off the vehicle and lights before changing keys.
Does this exact version have heated lenses?
Yes. Request Frost-Free after startup using the guide’s high-beam sequence. It operates only when its temperature and other conditions allow.
Does it have a startup welcome sequence?
The heated Evo includes a multistage welcome sequence.
What should I plan for installation?
Follow the original-equipment wiring branch, make the specified fuse-box-lid notch for the DRL wire, secure the wiring and adjust aim.
Are the Supercharged drivers included?
No. Standard drivers are supplied. LF2-DRVSC11 is the exact optional Supercharged pair, for off-road use only in Canada and the United States.
Will Frost-Free clear heavy overnight snow?
It helps mitigate buildup while driving in cold conditions. It is not a heavy overnight-snow defroster, and defaults off after each ignition cycle.
What warranty is included?
Morimoto lists a five-year limited manufacturer warranty. Keep proof of purchase and contact BTS for installation support or a suspected warranty issue.

























